spare wheel RENAULT TWINGO RS 2009 2.G Panelwork Workshop Manual

41A-24
FRONT LOWER STRUCTURE
Front half unit: Description
C44
41A
Right-hand side
There is only one way of replacing this part:
-complete replacement.
I - COMPOSITION OF THE SPARE PART
Left sideRight-hand side
125411
IMPORTANT
Use a repair bench to ensure the positioning of the
points and the geometr y of the axle assemblies.
120631
No. Description Type Thic-
kness
(mm)
(1) Front side mem-
ber closure panelHEL1.4
(2) S ide member,
front sectionHEL1.5
(3) Wheel arch Mild
steel1.2
(4) Cup height adjus-
terMild
steel1.3
120630
No. Description Type Thic-
kness
(mm)
(5) S ide member,
front sectionHEL/
Mild
steel1.5
(6) Front side mem-
ber closure panelHEL1.4
(7) Wheel arch Mild
steel1.2

41D-2
REAR LOWER STRUCTURE
Rear floor: Description
41D
II - PART FITTED
1 - Partial rear replacement
2 - Complete replacement No. Description Type Thic-
kness
(mm)
(1) Cross member HLE 1.5
(2) Reservoir front
centre mountingHLE 1.17
(3) Rear seat run-
ners front stiffe-
nerMild
steel1.2
(4) Rear floor Mild
steel0.65
(5) Rear tow eye
mountingMild
steel1.8
(6) Emergency spare
wheel bridge
mounting piece
unitMild
steel1.17
(7) Emergency spare
wheel arch rear
stiffenerHLE 1.5
(8) Left-hand rear
seat stiffener
mountingHLE 1.7
(9) Rear seat rear
centre stiffener
mountingHLE 1.7
(10) Right-hand rear
seat rear stiffe-
ner mountingHLE 1.7
120988
120987
WARNING
If the spot welds cannot be made as they originally
were with an electrical spot welding machine, they
should be replaced with securing beads.

42A-22
FRONT UPPER STRUCTURE
Front wheel arch: Description
42A
Front left-hand wheel arch
Front right-hand wheel arch
There is only one way of replacing this part:
-complete replacement.I - COMPOSITION OF THE SPARE PART
Front left-hand wheel arch
120930
120929
IMPORTANT
Use a repair bench to ensure the positioning of the
points and the geometr y of the axle assemblies.
120906
No. Description Type Thic-
kness
(mm)
(1) Wheel arch Mild
steel1.2
(2) Angle bracket Mild
steel2
(3) Shock absorber
cup height adjus-
terMild
steel1.3
(4) Wiper motor fixed
supportMild
steel1.6
(5) Shock absorber
cupMild
steel2

44A-14
REAR UPPER STRUCTURE
Inner rear wheel arch: Description
44A
There is only one way of replacing this part:
-complete replacement.
I - COMPOSITION OF THE SPARE PARTII - PART IN POSITION
Complete replacement
121041
IMPORTANT
Use a repair bench to ensure the positioning of the
points and the geometr y of the axle assemblies.
121012
No. Description Type Thic-
kness
(mm)
(1) Seatback retai-
ning hookHLE1.2
(2) Seatback fixed
mountingTHLE2
(3) Inner wheel arch Mild
steel0.75
(4) Rear seatback
fixed mounting
reinforcementHLE1.2
(5) Shock absorber
mounting cupMild
steel1.5
(6) Shock absorber
turret mountingHLE2
121013
Note:
For more detailed information on welded connec-
tions with three thicknesses, see MR 400.
IMPORTANT
If the mating faces of the parts to be welded are not
accessible, make EGW plug welds to replace the
original resistance welds (see MR 400).